Dme Toggle-Lok (Positive early ejector return) Manual do Utilizador descarregar pdf

Page 1 of 5 TL-9997 03/2010

ME-0508-PS-059(B)



DME TOGGLE-LOK

POSITIVE EARLY EJECTOR PLATE RETURN

INSTALLATION INSTRUCTIONS FOR STANDARD TOP MOUNT CATALOG NO. TLTM-100

Failure to comply with these warnings may lead to

personal injury. COMPONENT FALL DUE TO

GRAVITY. PINCH OR CRUSH HAZARD.

The DME Toggle-Lok assembly is comprised of lever arms which when partially unfastened

from a mold and released, may swing down due to gravity. Care needs to be taken when

installing, adjusting or repairing this assembly, either on a bench or in an injection press.

When servicing while the mold while it is installed in an injection molding press, always

ensure the press guard doors are interlocked with the operation of the machine platens. Do

not attempt to service this product while the mold is in the press if the press guard doors are

not interlocked with the operation of the machine platens. It is safer and more effective to

service the mold when it is on a work bench. Wear proper protective equipment including

gloves and eye protection. These instructions must be passed on to the end user who

should read them carefully before using this product. Failure to do so may result in serious

injury.

Installation instructions:

The Top Mount is used when the ejector plate extends beyond the end of the mold, since it

is designed to be mounted on top of the ejector plate. Refer to the table provided in the

DME Mold Components Catalog for the specific Top Mount required for your Toggle-Lok

package.

NOTE: Please refer to the DME Mold Components Catalog page titled, “Basic Design

Guidelines for Standard Mold Bases,” for additional information.

1. Entire setup is made with mold in the fully closed position.

2. Machine clearance for the lever on either end of the mold where the housing is open for

the ejector plate and place the lever in its proper position:

a) Central to mold if style X

b) As specified in table for style Y

c) As far out from centerline of mold as possible, keeping mounts on ejector plate

for style Z.

3. Check to be sure levers, mounts, arms and joints including their mounting screws and

dowels will not interfere with other mold components through their entire movement.

4. The lead-in end of all levers must be the same height and sides must be square to the

top of the mold. Locate and drill, or transfer if lever has mounting holes for two 3/8-16

1 2 3 4 5

DME TOGGLE-LOK 1
TL-9997 03/2010 2

Resumo do Conteúdo

Página 1 - DME TOGGLE-LOK

Page 1 of 5 TL-9997 03/2010 ME-0508-PS-059(B)DME TOGGLE-LOK POSITIVE EARLY EJECTOR PLATE RETURN INSTALLATION INSTRUCTIONS FOR STANDARD TOP MO

Página 2 - TL-9997 03/2010

Page 2 of 5 TL-9997 03/2010 ME-0508-PS-059(B)UNC S.H.C.S. Tighten S.H.C.S. and check for proper location and squareness. Maintaining corre

Página 3

Page 3 of 5 TL-9997 03/2010 ME-0508-PS-059(B)11. Repeat steps 6, 7, 8, 9, 10 on opposite end of mold. 12. Place cover plates under Top

Página 4

Page 4 of 5 TL-9997 03/2010 ME-0508-PS-059(B)NOTE: DRAWINGS BELOW ARE FOR REFERENCE ONLY, AND ARE NOT TO SCALE. ALWAYS USE PROPER TEMPLATE

Página 5

Page 5 of 5 TL-9997 03/2010 ME-0508-PS-059(B)NOTE: DRAWINGS BELOW ARE FOR REFERENCE ONLY, AND ARE NOT TO SCALE. ALWAYS USE PROPER TEMPLATE

Mais documentos para Hardware Dme Toggle-Lok (Positive early ejector return)

Para ver o documento Dme Toggle-Lok (Positive early ejector return) Manual do Utilizador

Dme Toggle-Lok (Positive early ejector return) Manual do Utilizador (3 páginas)

Comentários a estes Manuais

Sem comentários

Dme Toggle-Lok (Positive early ejector return) Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Dme Toggle-Lok (Positive early ejector return). DME Toggle-Lok (Positive early ejector return) User Manual Manual do Utilizador

Resumo do Conteúdo

Mais documentos para Hardware Dme Toggle-Lok (Positive early ejector return)

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Dme Toggle-Lok (Positive early ejector return)